Square yards, square feet and linear feet: how flooring is measured and sold
How carpet, LVP and base are sold by square yard, square foot and linear foot, how to convert, and how roll width and cartons set what you order.
By Derek Spohn · Last reviewed November 2026 · 7 min read
In this guide
- The short answer
- Which products sell by which unit
- The conversions
- Nominal width and usable width
- Waste and trim allowance
- Order carpet by the cut
- Pattern match and pile direction
- Example 1: a bedroom from a 12 ft roll
- Example 2: the same bedroom from a 13 ft 6 in roll
- Example 3: an LVP living area in full cartons
- Common mistakes
- Checklist
- How Turn One handles this
The short answer
Broadloom carpet and pad are sold by the square yard (SY), LVP, tile and sheet goods by the square foot (SF), and base, transitions and stair nosing by the linear foot (LF) or by the piece. One SY is 9 SF, and a carpet cut’s yardage is the roll width in feet times the cut length in feet, divided by 9.
Carpet comes off a roll of fixed width and hard surface comes in sealed cartons, so what you order is almost never the room’s area.
Which products sell by which unit
- Broadloom carpet: SY. Rolls are most often 12 ft, 13 ft 6 in or 15 ft wide.
- Carpet pad (cushion): SY. Pad is pieced and taped at the seams and has no pile direction, so order close to the room’s area, then round to the rolls your supplier sells (often 30 to 40 SY a roll).
- LVP, plank and tile: SF, in cartons. The carton label gives its SF, and you buy whole cartons.
- Sheet goods: SF, though some suppliers still price sheet vinyl by the yard. It comes off a roll, so plan it by the cut like carpet.
- Base, transitions and stair nosing: LF or by the piece. Base comes in coils or set lengths. Transitions and nosing come in set lengths, one per doorway or tread.
Labor usually follows the same units: carpet per SY, hard surface per SF, base per LF, or a flat rate per unit on turns.
The conversions
- 1 SY = 9 SF, because a yard is 3 ft and 3 x 3 = 9.
- SF to SY: divide by 9. SY to SF: multiply by 9.
- Price: $27.00 per SY / 9 = $3.00 per SF (example).
- Inches to feet: divide by 12. 3 in is 0.25 ft, 4 in is 0.333 ft, 6 in is 0.5 ft, 9 in is 0.75 ft.
- Roll yardage: SY = width ft x length ft / 9. On a 12 ft roll, every LF you cut is 12 / 9 = 1.33 SY, so 3 LF is exactly 4 SY. On a 13 ft 6 in roll, every LF is 1.5 SY. On a 15 ft roll, it’s 1.67 SY.
- Base: perimeter minus openings. Example: a 12 by 14 ft room has 2 x (12 + 14) = 52 LF of wall. Take out a 3 ft doorway and you need 49 LF before waste.
Nominal width and usable width
The width on the label is nominal. The usable width is what you can actually lay. Installers trim factory edges for a clean seam, edges get crushed in shipping, and a roll can come in a few inches under its label.
Plan on usable width. When a room is within a few inches of the roll width, put a tape across the actual roll before you promise no seam.
Rolls come up short on length, too. We hit it more than once, and sometimes it was the last roll, so we had to reschedule the job or swap materials. Sometimes that cost us the customer. Check the real feet left before a job goes on the schedule.
Waste and trim allowance
Carpet is cut oversize and trimmed at every wall. A common allowance is about 3 in at each wall, so add 6 in to each dimension of the cut. Ask your installers. On top of trim there’s fall-off, the strip of roll width the room doesn’t use.
For hard surface, add a percentage to the room’s area, then round up to full cartons. Around 5 to 10 percent is common for a straight lay in an open room, and it’s what held up on our apartment turns. Diagonal, herringbone or lots of closets need more.
Decide whether you sell and pay installers on gross (what was ordered or cut) or net (the room’s area), and write it down.
Order carpet by the cut
With carpet you pay for the full roll width over every foot you cut, whether the room uses it or not. So draw the room first:
- Decide which way the roll runs.
- Mark any seams and fills. A fill is a narrow piece covering what the main piece can’t.
- List each cut as width x length, with trim added.
- Add the lengths, multiply by the roll width, divide by 9.
Fills have to come from the same roll with the pile running the same way. Label fall-offs with the roll, width and length so they become the next unit’s closet or fill instead of trash.
We lost a lot of material we could have used again, because we had no easy way to get it back into the system. Make logging a fall-off back into stock quick, or it won’t happen.
Pattern match and pile direction
Carpet fibers lean one way. Run your hand across it: smooth one way, rough the other. That’s the pile direction. Every piece, including through doorways, should run the same way, or the seam shows as two shades. That’s why you can’t spin a fill sideways to save carpet. Mark the direction on the cut sheet.
Patterned carpet repeats every so many inches, listed on the spec sheet. Seamed pieces have to line up, so each cut length rounds up to the next full repeat. Example: a 13 ft 6 in cut on a 24 in (2 ft) repeat is 13.5 / 2 = 6.75 repeats. Round up to 7, and the cut becomes 14 ft. A half-drop pattern, where the design shifts half a repeat from one edge to the other, needs extra length to match. Most apartment carpet is solid, but check.
Example 1: a bedroom from a 12 ft roll
Example room: 11 ft 3 in by 13 ft 0 in, no closet. Example price: $27.00 per SY.
- Room area: 11.25 x 13 = 146.25 SF. 146.25 / 9 = 16.25 SY.
- Run the 12 ft width across the 11 ft 3 in side. With 6 in of trim it needs 11 ft 9 in, leaving 3 in to spare.
- Cut length: 13 ft + 6 in trim = 13.5 ft.
- Cut: 12 x 13.5 = 162 SF. 162 / 9 = 18 SY.
- Over the room’s area: 18 minus 16.25 = 1.75 SY (15.75 SF) of trim and fall-off.
At $27.00 per SY, the cut is 18 x 27 = $486.00. Quoted on area alone, it would be 16.25 x 27 = $438.75, which leaves $47.25 of carpet unpaid. Pad goes in near the area: about 17 SY.
Example 2: the same bedroom from a 13 ft 6 in roll
Same room, same price, on a 13 ft 6 in roll. There are two ways to run it. Pile direction usually has to match the hall carpet through the doorway, which can decide which way the roll runs.
Width across the 13 ft side. With 6 in of trim that side needs 13 ft 6 in, the full nominal width. The cut length is 11 ft 3 in + 6 in = 11.75 ft. The cut is 13.5 x 11.75 = 158.625 SF, and 158.625 / 9 = 17.63 SY. That’s the smallest cut, but only if the roll really is 13 ft 6 in. If it comes in 3 in under, you’re down to 1.5 in of trim at each wall, which most installers won’t accept.
Width across the 11 ft 3 in side. The cut length is 13.5 ft. The cut is 13.5 x 13.5 = 182.25 SF, and 182.25 / 9 = 20.25 SY. That’s 2.25 SY more than the 12 ft roll, or 2.25 x 27 = $60.75. You also get a fall-off 1 ft 9 in wide and 13 ft 6 in long.
For this room the 12 ft roll is the safer buy. The wider roll earns its keep when a room is wider than about 11 ft 6 in and it saves you a seam.
Example 3: an LVP living area in full cartons
Example room: 15 ft 4 in by 18 ft 9 in. Example carton: 22.5 SF. Example price: $3.00 per SF. Example waste: 8 percent for a straight lay.
- Convert: 15 ft 4 in is 15.333 ft, and 18 ft 9 in is 18.75 ft.
- Area: 15.333 x 18.75 = 287.5 SF.
- Add waste: 287.5 x 1.08 = 310.5 SF.
- Cartons: 310.5 / 22.5 = 13.8. Round up to 14 cartons.
- Ordered: 14 x 22.5 = 315 SF. Cost: 14 x $67.50 a carton = $945.00.
Thirteen cartons would be 292.5 SF, only 5 SF over the bare area. Some property managers want a carton left for repairs, so ask before leftovers go back to the shelf.
Common mistakes
- Quoting carpet on the room’s area times a percentage.
- Planning on the label width instead of the usable width.
- Rounding cartons down, or using another product’s carton size.
- Turning a fill sideways to save carpet.
- Writing a number without its unit. “240” could be SF or SY.
- Trusting the property’s floor plan over your own tape.
Checklist
- Measure each floor plan yourself once, to the inch, keep it on file, and re-check any unit that looks different.
- Note each product’s selling unit: SY, SF, LF or piece.
- Carpet: check usable width, draw the cuts, add trim, keep the pile one way, round up for any repeat.
- Hard surface: area plus waste, divided by the carton’s SF, rounded up.
- Base: perimeter minus openings, plus waste, rounded to whole pieces or coils.
- Record the fall-offs.
How Turn One handles this
Turn One’s quotes keep every line in the trade’s units, carpet in SY, plank in SF and base in LF, and the roll math is done for you, so 63 LF off a 12 ft roll shows as 84 SY. Every quote shows cost, gross profit and margin before it goes out, and the approved quote becomes the job, with the cut list and invoice coming from it. More on the Quoting page.
Derek Spohn built a multifamily flooring company from scratch to more than 20 crews. He started Turn One. Questions or a correction? Email contact@getturnone.com.
More guides
- How to invoice a property management company (and get paid sooner)What property management AP needs on every flooring invoice, where to send it, and how to follow up without souring the account.8 min read
- Margin vs. markup for flooring contractorsThe difference between margin and markup on a flooring job, how to convert one to the other, and why mixing them up costs you money.2 min read
- Outgrowing QuickBooks and spreadsheets: a switching plan for a flooring shopSigns your flooring shop has outgrown QuickBooks and spreadsheets, what moves to new software, when to cut over, and a switching checklist.7 min read
- How to quote an apartment unit turn (and keep the margin)What goes in a flooring turn quote, how to price it from cost and margin, and the approval and follow-up steps that keep the money.7 min read